Shepherd Hardware 9240 1-Inch Square Adhesive, Slide Glide Furniture Sliders, 8-Pack, Tan

Rating these 5 stars even though the screws included do not work on my  Ghost Chairs . The chairs have a grippy silicone insert on the bottom of the legs, exactly the same size as the Shepherd sliders, but screws have to be a little longer to reach penetration. I used the stick-on option temporarily until I can find screws the exact size I need. Too short and they don't penetrate the silicone, too long and they hit the hard plastic of the chair, thereby weakening it. I'll find them and make the permanent attachment, but the adhesive sliders are staying in place perfectly meanwhile. The silicone grippers are exactly opposite of what is needed on the vinyl flooring, causing difficulty sliding the chairs under the table. The Shepherd sliders are the perfect answer to the issue.UPDATE 9/14/17: Proper sized screws now installed for the plastic chairs with guide hole drilled and tightened down snugly... I am very pleased with the result because I feel it adds a lot of security to those fairly expensive chairs. The screw length is in no way Shepherd Hardware's fault, they include screws that would fit almost any other chair, but the ghost chairs have about a one inch space before the screw hits home.UPDATE 3/26/18: 6 months later, not one single problem with these staying screwed in place and sliding nicely on the vinyl flooring.

I installed these on four legs of a lamp table. Each leg had a 3/8 in hole already drilled in it- why I don't know. I was still able to drill using an 1/8-in drill bit into the leg and mount the slider. Push out the hole in the slider compression material with a nail or the screw. Remove the backing, and affix the slider to the bottom of the leg. Then drill a hole into the leg through the hole in the slider. Slowly pulse drill the screw into the hole. The backing will compress as the screw tightens the slider against the leg. Check the amount of visible compressed material- black- to make sure that each slider is the same height above the table leg. Less compressed will result in a slightly longer leg than a more compressed material. Alternately, remove the compressable material before installing. In that event, you can mark the hole or try drilling through the hole in the slider.The screws are easy to screw in, so you don't need to drill very deep. These sliders are high quality. I was very pleased with the result. Highly recommend.

It meets my expectations. The self adhesive is a bonus.

Used on an heavy antique cabinet. Removed the adhesive. Had no trouble with the screws, had predrilled holes and used a hand screwdriver. Slides on vinyl tile well if I need to move it.

I am using these for my 8 wood dining chairs that sit on our tiled floor. I had applied these to 4 chairs when I wrote my original review <<see below>>. Then I decided to use a larger drill bit than I normally would as it seems these screws just can’t bite into the wood on their own (another reviewer said these are sheet metal screws, so maybe that’s the problem). Since these screws have a Phillips head that allows for a fat flat head screwdriver, I drove the final 16 screws in that way.After applying these to all my dining chairs, they no longer make a screeching sound when pushing the chairs in after we get up from the table. They glide more smoothly (on our tile floors) whether the chairs are occupied or empty.I tested them on my wood floor. They don’t glide as easily & I’d be afraid that over time, as the glider wears down, it might scratch the wood. Tested on my wool Persian rug & the chair won’t slide while sitting on it. Tested on my low pile cut loop carpet & they don’t move. I’m only 125#, so that’s not the reason they don’t glide on carpet.To make them look good on my stained chairs, I did the following:• removed the white pad from the glider• used a black marker on the visible part (4 sides) of the grey gliders• centered the glider on the bottom of my chair leg & marked the hole with my drill bit• set the glider aside & drilled my hole into my chair leg the full length of the screw• lined up the glider & applied the screw using a hefty flat head screw driver - don’t ever tighten or washer will push through the black base• then I set the chairs upright & could barely see the new (black) gliders on the bottoms of my chair legsOriginal review, titled: “Not worth the money or the aggravation” <<Like another reviewer wrote (which I didn’t read until after working in these), the screws are terrible. A few spins of my electric drill to get them into a predrilled hole, & the heads strip out.The pad that has adhesive on it squishes unevenly when using it, so I removed them. The white adhesive pad against the black base looks tacky anyway.The black part of the disc is too soft which allows the metal washer that is embedded in it to push through while applying the screw.>>

We've been through lots of products trying to protect a softer cherry floor from hard wood dining chair bottoms. These match the shape of the chair legs (more or less square) and cover more of the bottom than the round options plus they stay on and are easily cleaned (of cat hair mostly) unlike the slip on felt guards we had been using. Super economical - we use the provided screw along with the adhesive and everything stays secure. I am literally on my third purchase of 2 sets because we keep finding original or add-on equipment failures that these take care of at a low cost! Crazy that we spend so much on so many products and a handful of bucks shelled out for something that we don't really even see bring more satisfaction than they ought to :-).

We have wood floors and wanted something that would let us slide our couches and coffee table easily in order to vacuum. These work great for that task and also for just generally moving things. Having a screw to attach is a must Is all the previous adhesive only pads collected hair, dust, etc. and always fell off shortly after installing. I love the square shape too. You don’t even see them on the bottom of the couch legs. Highly recommend these sliders.

Great product. Attaches firmly glides effortlessly. Nor pickup of dust or hair. No felt!