Lumitronics RV Surface Mount Light, Stop/Turn/Tail for RV, Trailer, Camper, 5th Wheel, Motorhome (White)

Got this for my early '90s travel trailer. It has rounded corners where the original had square corners. Regardless, it was an exact fit. Easy to install. I soldered the connection and used shrink tube for insulation, but could just have easily used crimp connectors. I used Vulkem to seal the gaps due to the corrugated aluminum siding on the trailer. It's bright and looks so much better than the old ones. Note that this one does have a license plate holder integrated. I used it on the Left side of the trailer.

Easy to install and they look so much better then the old original ones on my trailer. Good value and quick service. Good clean units with every thing you need other then screws.NOTE: if you get the light with the license plate holder, you will need to put the license plate on before you attach the unit to your trailer. The instruction did not mention this! It was a real pain to try to get the plate on after instillation.I dropped my rating on this because of that!

I don't know what the difference is between this and the Optronics light (other than $6.50) but this works great and looks so much like the Optronics passenger side light that they don't look mismatched. The Optronics light was backordered so I ordered this before our camping trip figuring that if it didn't match I would wait for the Optronics to come. Turns out it was just find. When the Optronics one did come I just sent it back saving myself over $6. It's nice to have actual license plate holders again rather than what I had cobbled together before and for $10 it was a no brainer. Went together pretty easily though didn't match my original screw holes. Filled the old ones with silicone and I am good to go.

These are dirt cheap and you get what you pay for and maybe a little more. Our left tail light was out as we did our light test upon trying to leave. I went out and bought some light bulbs but the problem was more than the bulb. The spring had rusted from being under water so much. These do not seal very well where the lens meets the body of the fixture. Whatever... it lasted 5 years and costs so little to replace. I was able to rig the light into working for our trip but when I got home I ordered a replacement. The replacement was exact and easy to install. I'm not complaining if these last five years, but I'd much rather spend more money and have them never break. You can't complain about the price being too high with these. This is the state of the art with the RV world. There are few things made well.

Fit our 2013 Pacific Coachworks 2013 Panther 22XL PERFECTLY! You will need screws/bolts and nuts to attach license plate, which should obviously be done before installing light plate. I ran a bead of clear silicone caulk around the edge of the plate after installing it to allow me to replace it again, if needed. You will also need wire stripper, wire nuts, etc. to wire the new assembly, which does include a bulb. Note: You may need new screws to attach the plate to your trailer (or whatever), but all the holes in my trailer for the old light aligned perfectly with this new one.

If your looking for a affordable way to replace or upgrade your lights these are the way to go, these replaced my original lights on my 04 Jayco pop up and they are so much brighter during the day and look great. Always replace in pairs since theses are so much clearer than original, easy to install all you need is some 18 awg crimp connectors and a wire stripper with a little caulk and your set.

Crappy product in my opinion, even crappier when a product is shipped out with damage. There are two different types of lens one for tag and one for the passenger side. I could not get a straight answer from the seller or anyone else for that matter, on wiring WITHOUT backup lights or if the two lenses were identical in appearance as one was shown with a clear lens for backup light. The ones I was shipped DIDNOT have a clear lens, a confusing and aggravating experience. Sent both back and found a BETTER product!!

Got this for my early '90s travel trailer. It has rounded corners where the original had square corners. Regardless, it was an exact fit. Easy to install. I soldered the connection and used shrink tube for insulation, but could just have easily used crimp connectors. I used Vulkem to seal the gaps due to the corrugated aluminum siding on the trailer. It's bright and looks so much better than the old ones. Note that this one does not have a license plate holder integrated. I used it on the Right side of the trailer.