SIKAAnchorFix-2 Super Strength Anchoring Adhesive - Two-Component System for Threaded Rods in Concrete, 10.1 fl. oz - Fast Curing, Solvent-Free, High Load Capacity

I had a cheap HF gun which couldn’t hack it, luckily my BIL had a very good one and that delivered the product just fine. It sets pretty fast even at 50º ambient but things can move for a while if not attended to.I set four 4x4 post bases that have a 9” rebar welded onto the bottom in a rock bald which was grey shale, it did not scale or shatter when I drilled it and remained very solid. I used a 1” bit to give me some wriggle room alignment wise, filled the holes 3/4’ full and pressed the bases in, a good bit flowed out the top as I set them. Over the next hour they shifted slightly and went out of alignment a tad but I coerced them back into place. They will be supporting an 8’x6’ covered porch so I probably didn’t need adhesive at all, the weight of the porch being what it is. The recommendation for a 3/4” post pin is a 7/8” hole but I didn’t have a 7/8” rotary hammer bit, only 3/4” and 1”, so 1” it was.I cut about 2” off the end of the mixing nozzle but didn’t cut back to the point where the mixing labyrinth is. I pumped out about 6” of product on a paper towel but should have done more, the gun wasn’t cooperating, by doing more it insures that only well-mixed product goes in the hole and more importantly stays in the nozzle - many people have trouble with the nozzle clogging but it’s often because they failed to follow the instructions on the tube imo. A high quality and high power caulk gun is mandatory imo.

For the last month, I have been trying to glue down some paver steps in my backyard. I have tried a half a dozen products, all of which were advertised as "strong adhesives" for pavers. None of them worked. I used this product today and it was unbelievable! It did everything I needed it to do. I knew as soon as I applied it and the pavers stuck that this product was probably going to work really well. It's a been a few hours now and those paver steps aren't going anywhere!Super pleased with this product! It's not the cheapest product on the market, but, boy, does it work. Given the amount of time I've spent applying and then removing other products, I should have bought this the first time. It was well worth the price!

I will take some ownership of this issue, but honestly I wasn't dawdling that long.I had four bolts to set in a wall. Pumped in the epoxy for the first and was a bit slow putting in the bolt. By the time I was working on the second the epoxy had already set up in the nozzle. Switched nozzles and managed to get #2 done but that was it.This stuff holds, but sets quickly.

This stuff dries very quick but is strong as concrete. Used to anchor 2 small concrete pads together with rebar.

Product looks fine but they broke off the two feed tubes and then only packed one in the box so now I either have to buy another tube or the rest after the two posts I'm installing just goes to waste.

This stuff works. Be prepared by having two people. One glues, one sets the rebar. You can go through the whole tube without a problem of it setting up too fast and each piece will be placed where you want it and hold, even if you beat on it with an 8 pound maul to bend it.

Used to secure bolts holding newel posts into concrete. Worked great, posts are solid

Seller must be distribruting old expoxy. We had literally the same issue as another guy. We used our best heavy duty caulking gun and it would not even exit the tube!I'm saying this is true: "I followed the instructions, removed the cap, cut the bag below the clip, inserted in a caulking gun and started to squeeze out a little to get the mixing started. Literally 10 seconds or less later tried to squeeze into the hole I had pre drilled and it was already hard in the mixing tube. I cut the nozzle back 3 inches and it was still too hard to squeeze out, broke my gun. I tried the second nozzle and another caulking gun and got one hole filled before the epoxy was hard in the nozzle again. Decided to open the whole thing up squeeze out the epoxy on a board and give it a hand mix..."Clearly defective product. Buy it from a box store instead.