SPARIN [2-Pack Screen Protector Compatible with Microsoft Surface Go 2/Surface Go, Tempered Glass, High Responsive, Scratch Resistant

Es lo que esperaba. Lo tengo hace un tiempo y me funcionó bien

Made my screen unusable. The sensitivity was different and inconsistent throughout my screen. Some areas would double tap, some would just not respond at all. Scrolling became impossible.Update:After rebooting the computer, it started working well. No change in sensitivity for the tablet.

This screen went on fast and was actually easier than the one I put on my cell phone which cost much more. The tabs are key. First, watch the youtube video. It shows putting 2 tabs on the short side, I used 3 tabs on the long side. The protector is very very slippery and I didn't have a helper to hold it in place while I attached the hinge tabs to the screen. So what I did (BEFORE removing film) was position it by using a small piece of scotch tape in the middle of each short end, applying the tape to the protector top first. You can then ease it in in place and make fine adjustments without worrying about messing up the provided hinge tabs. Press these scotch tape pieces to the edge of the Surface Go and double check alignment. Adjust if necessary until perfect. THEN put the 3 hinges on the long side. When these hinges are folded over and attached to the protector you can take off the scotch tape pieces and proceed to cleaning. Important: make sure there is no slack in the hinge when folding over onto the protectorI have hot air heat in my house which blows around a lot of dust. I turned the thermostat down (or up if you have A/C) so the system wouldn't trigger and start blowing dust around in the middle of my installation. I also wiped down the surface I was working on, and washed and dried hands with a microfiber dish cloth. I used wet swab, then dry swab then tacky strip. I removed the film steadily and quickly trying not to stir up any air current. (don't let the sticky side touch anything after the film is off!) I closed the hinge and it immediately started adhering from the hing side across the screen until it was solidly on. Not one piece of dust or bubble, and perfect alignment! Love it!

Functions well. Bubble removal not needed if you follow instructions carefully. Touch sensitivity fair. Easy to apply as much as these things can be. Clarity for sure.

Bought for Surface computer, and it was easy to install, I had a bubble on the first attempt but the YouTube showed to get rid of it, and it was gone within a few minutes.

Wanted to be sure to protect the screen of my new Microsoft Surface Go. The Spring Screen Pro pkg comes with two very high quality screen protectors, two wet cleaning cloths, two drying cloths, six guide stickers, two micro cleaning cloths, two dust removers/absorbers, and one bubble removal card (I used a credit card). It also comes with a step by step instruction manual in English, Chinese, and pictures.I was really impressed with the quality of all of the materials. The screen protectors are 9H, clear HD, anti-scratch, premium tempered glass. This all comes in a sealed rigid protective box for easy storage and protection of the second set of materials while in storage or in transit.Considering the fact that I usually mess up my first go round with screen protectors, I'm really glad that there were twosets of everything. (and I did mess it up by forgetting to use the dust absorber/remover, which is the last step before installation. Thus...lots of bubbles, which was completely my fault) Follow the directions in the instruction manual, and you'll get a flawless installation.Great value & Highly recommended!

I bought this for my new Surface Go. I was happy to see these were thick plastic protectors and not just a film. It was fairly easy to put on even though I didn't use the little stickers that came with it as a guide.I just returned home from a last minute trip out west, where I had to fly, and had taken my Surface Go with me. While on the plane I accidentally knocked it off the tray table and it landed screen down on the aisle, hitting the side of the seat as it fell. I was devastated to see cracks in the screen and a little chip off the side, especially since I had not purchased the insurance from Mircosoft. When I got home I peeled off the screen protector and was absolutely thrilled to find the screen was in perfect condition. The screen protector had multiple scratches and cracks from the fall, but it saved the screen from any damage. Since this was a two pack, I've already put on the 2nd protector.I would definitely recommend this to anyone.

I was a former ZAGG Customer and I got so tired of paying $30 -$40 For my countless devices screen protectors it just got old. Not to mention I’m pretty tough on my devices I break a screen protector probably I’d say at least two a month if not three maybe sometimes one a week. And then to have to deal with zagg’s Number one return policy but number two they feel that you’re frauding them every time so they cancel your first request regardless of your history with them it’s just stupid. I’ve ordered at least four or five replacements through sparin it’s super easy I just do it through Amazon messaging I gave them my order number and that’s it all of a sudden it shows up at my door within a day or two simple EZPZ!I mean if you haven’t figured it out all the screen protectors of the same YP sometimes 10 times more for what you can get through this company thank you and keep up the good work guys and gals